Search Results

An experimental investigation of the spectral characteristics of turbulent flow in a scale model of a high pressure diesel fuel injector nozzle hole has been conducted. Instantaneous velocity measurements were made in a 50X transparent model of one hole of an injector nozzle using an Aerometrics Phase/Doppler Particle Analyzer (PDPA) in the velocity mode. Turbulence spectra were calculated from the velocity data using the Lomb-Scargle method. Injector hole length to diameter ratio (L/D) values of 1.3, 2.4, 4.9, and 7.7 and inlet radius to diameter ratio (R/D) values of approximately 0 and 0.3 were investigated. Results were obtained for a steady flow average Reynolds number of 10,500, which is analogous to a fuel injection velocity of 320 m/s and a sac pressure of approximately 67 MPa (10,000 psi). Turbulence time frequency spectra were obtained for significant locations in each geometry, in order to determine how geometry affects the development of the turbulent spectra.

This research focused on the effects of split injection on fuel spray behavior in a diesel environment. It was done in a special designed engine-fed combustion chamber (swirl ratio of 5) with full field optical access through a quartz window. The simulated engine combustion chamber used a special backwards spraying injector (105°). The electronically controlled injector could control the size and position of it's two injections. Both injections were through the same nozzle and it produced very rapid injections (1.5 ms) with a maximum injection pressure of 130 MPa. Experimental data included: rate of injection, injector pressure, spray plume images, tip penetration, liquid and vapor fuel distributions, combustion pressure, and rate of pressure rise. From 105° forward scatter images, tip penetration was observed to be very rapid and reached a plateau at 25 mm.

The three-dimensional KIVA code has been used to study the effects of injection pressure and split injections on diesel engine performance and soot and NOx emissions. The code has been updated with state-of-the-art submodels including: a wave breakup atomization model, drop drag with drop distortion, spray/wall interaction with sliding, rebounding, and breaking-up drops, multistep kinetics ignition and laminar-turbulent characteristic time combustion, wall heat transfer with unsteadiness and compressibility, Zeldovich NOx formation, and soot formation with Nagle Strickland-Constable oxidation. The computational results are compared with experimental data from a single-cylinder Caterpillar research engine equipped with a high-pressure, electronically-controlled fuel injection system, a full-dilution tunnel for soot measurements, and gaseous emissions instrumentation.

Many researchers have studied and developed methods for on-board engine combustion misfire detection in production vehicles. Misfiring can damage the catalytic converter within a short time and can lead to increased emission levels. For that reason, the on-board detection of engine misfire is one requirement of the On Board Diagnosis II (OBDII) Regulation and a recent interest for many researchers. One object in this paper is to propose a misfire detection method for multi-cylinder SI engines. The detection is achieved by examining the estimated cylinder pressures and combustion heat release rates in engine cylinders. The Sliding Observer methodology is applied in these estimations. This detection method provides a reliable and low-cost way to diagnose engine misfires. The other object of the paper is to eliminate large estimation errors due to system unobservability and reconstruct cylinder pressures.

Nonlinear observer theories are applied to the engine estimation problem in order to reconstruct engine states based on the measured engine variables, and dynamic mean torque production and cylinder-by-cylinder engine models. Engine cylinder and intake manifold pressures are two important factors in engine control and diagnostics. This paper discusses how to design nonlinear engine cylinder pressure and intake manifold pressure observers that have good robustness and estimation accuracy. Sliding mode theory in Variable Structure Systems (VSS) have shown good performance and been successfully applied to many nonlinear systems. Accordingly, sliding observers are selected for this study.

This study was conducted to develop an understanding of how rate-shaped and split injections can affect the soot and NOx emissions of a heavy-duty diesel engine. The tests were performed on a single cylinder version of the Caterpillar 3406 production engine, modified to accept an electronically-controlled, high-pressure common-rail injection system that offers a very high degree of flexibility in injection timing, split injections, and rate shaping of the initial injection. The engine was instrumented for particulate measurements with a full dilution tunnel, and CO, CO2 and NOx emission meters. Cylinder pressure was used to study heat release rates, and the response to changes in the injection scheme. The results show that rate-shaped injection, when optimized for lowest BSFC, does not appreciably affect pressure rise or peak cylinder gas pressures.

Studies of transient diesel spray characteristics at high injection pressures were conducted in a constant volume chamber by utilizing a high speed photography and light extinction optical diagnostic technique. Two different types of nozzle hole entrances were investigated: a sharp-edged and a round-edged nozzle. The experimental results show that for the same injection delivery, the sharp-edged inlet injector needed a higher injection pressure to overcome the higher friction loss, but it produced longer spray tip penetration length, larger spray angle, smaller droplet sizes, and also lower particulate emission from a parallel engine test. For the round-edged and smooth edged tips at the same injection pressure, the sharp-edged inlet tip took a longer injection duration to deliver a fixed mass of fuel and produced larger overall average Sauter Mean Diameter (SMD) droplets.

An emissions and performance study was performed to show the effects of injection pressure, nozzle hole inlet condition (sharp and rounded edge) and nozzle included spray angle on particulate, NOx, and BSFC. The tests were conducted on a fully instrumented single-cylinder version of the Caterpillar 3406 heavy duty engine at 75% and 25% load at 1600 RPM. The fuel system consisted of an electronically controlled, hydraulically actuated, unit injector capable of injection pressures up to 160 MPa. Particulate versus NOx trade-off curves were generated for each case by varying the injection timing. The 75% load results showed the expected decrease in particulate and flattening of the trade-off curve with increased injection pressure. However, in going from 90 to 160 MPa, the timing had to be retarded to maintain the same NOx level, and this resulted in a 1 to 2% increase in BSFC. The rounded edged nozzles were found to have an increased discharge coefficient.

A study was performed to correlate the Sauter Mean Diameter (SMD), NOx and particulate emissions of a direct injection diesel engine with various injection pressures and different nozzle geometry. The spray experiments and engine emission tests were conducted in parallel using the same fuel injection system and same operating conditions. With high speed photography and digital image analysis, a light extinction technique was used to obtain the spray characteristics which included spray tip penetration length, spray angle, and overall average SMD for the entire spray. The NOx and particulate emissions were acquired by running the tests on a fully instrumented Caterpillar 3406 heavy duty engine. Experimental results showed that for higher injection pressures, a smaller SMD was observed, i.e. a finer spray was obtained. For this case, a higher NOx and lower particulate resulted.

Improved atomization is important in fuel injection applications since atomization influences fuel-air mixing and vaporization rates. The present paper explores the use of low pressure gas/air injection and methods to achieve a dispersed two-phase flow to enhance the atomization process. Gas-driven twin-fluid atomization has been achieved by combining X-ray lithographic/micro-machining technology to mechanically disperse a driving gas into a liquid to be sprayed. This technique forces the gas through a designed pattern of micron sized holes thereby yielding a field of micro-bubbles immediately upstream of the < I mm. diameter discharge orifice. Precise control of both uniformity of hole diameter and inter-hole spacing is critical to producing a well dispersed bubbly flow. The results show that the method of gas injection influences the liquid breakup process. Results are given for steady-flow atomization with low pressure injection into ambient air.

Planar instantaneous fuel concentration measurements were made by laser-induced fluorescence of 3-pentanone in the spark gap just prior to ignition in a direct-injection spark-ignition engine operating at a light load, highly stratified condition. The distribution of the average equivalence ratio in a circle of 1.9 mm diameter centered on the spark plug showed that a large fraction of the cycles had an equivalence ratio below the lean limit, yet acceptable combustion was achieved in those cycles. Further, weak correlation was found between the local average equivalence ratio near the spark plug and the time required to achieved a 100 kPa pressure rise above the motoring pressure, as well as other parameters which characterize the early stages of combustion. The cause for this behavior is assessed to be mixture motion during the spark discharge which continually convects fresh mixture through the spark gap during breakdown.

Control of the flow of thermal energy in an air-cooled engine is important to the overall performance of the engine because of potential effects on engine performance, durability, design, and emissions. A methodology is being developed for the assessment of thermal flows in air-cooled engines, which includes the use of cycle simulation and in-cylinder heat flux measurements. The mechanism for the combination of cycle simulation, the measurement of in-cylinder heat flux and wall temperatures, and comparison of predicted and measured heat flux in the methodology is presented. The methodology consists of both simulation and experimental phases. To begin, a one-dimensional gas dynamics code (WAVE) has been used in conjunction with a detailed in-cylinder flow and combustion model (IRIS) in order to simulate engine operation in a variety of operating conditions. The methods used to apply the model to the air-cooled engine case are described in detail.

A laboratory-based fuel mixture system capable of delivering a range of fuel/air mixtures has been used to observe the effects of differing mixture characteristics on engine combustion through measurement and analysis of incylinder pressure and exhaust emissions. Fuel air mixtures studied can be classified into four different types: 1) Completely homogeneous fuel/air mixtures, where the fuel has been vaporized and mixed with the air prior to entrance into the normal engine induction system, 2) liquid fuel that is atomized and introduced with the air to the normal engine induction system, 3) liquid fuel that is atomized, and partially prevaporized but the air/fuel charge remains stratified up to introduction to the induction system, and 4) the standard fuel metering system. All tests reported here were conducted under wide open throttle conditions. A four-stroke, spark-ignited, single-cylinder, overhead valve-type engine was used for all tests.

This paper describes the transient spray characteristics of a high pressure, single fluid injector, intended for use in a direct-injection spark-ignited (DISI) engine. The injector was a single hole, pintle type injector and was electronically controlled. A variety of measurement diagnostics, including full-field imaging and line-of-sight diffraction based particle sizing were employed for spray characterization. Transient patternator measurements were also performed to obtain temporally resolved average mass flux distributions. Particle size and obscuration measurements were performed at three locations in the spray and at three injection pressures: 3.45 MPa (500 psi), 4.83 Mpa (700 psi), and 6.21 MPa (900 psi). Results of the spray imaging experiments indicated that the spray shapes varied with time after the start of injection and contained a leading mass, or slug along the center line of the spray.

This paper reports on the investigation of injection pressure upon the droplet behavior in transient diesel sprays. Phase/Doppler results for a Diesel spray with a maximum fuel injection line pressure of 105 MPa are compared with previously acquired droplet size and velocity measurements for a Diesel spray with an injection pressure of 21 MPa. All measurements reported here were made in atmospheric conditions at a position near the nozzle. It is shown in these results that the droplet velocity and size profiles do maintain similarity despite the substantial change in injection pressure. Specific characteristics, for example, the appearance of subtle waves in the time-dependent spray data, are present in both data sets. Comparison of the measured droplet velocities and diameters with Weber number based stability criteria shows that increased injection pressure produces a higher percentage of droplets that are likely to breakup.

The objective of this study was to investigate the effects of fuel viscosity and the effects of nozzle inlet configuration on the characteristics of high injection pressure sprays. Three different viscosity fuels were used to reveal the effects of viscosity on the spray characteristics. The effects of nozzle inlet configuration on spray characteristics were studied using two mini-sac six-hole nozzles with different inlet configurations. A common rail injection system was used to introduce the spray at 90 MPa injection pressure into a constant volume chamber pressurized with argon gas. The information on high pressure transient sprays was captured by a high speed movie camera synchronized with a pulsed copper vapor laser. The images were analyzed to obtain the spray characteristics which include spray tip penetration, spray cone angle at two different regions, and overall spray Sauter Mean Diameter (SMD).

Liquid fuel penetration was measured using an endoscopebased imaging system in an operating single-cylinder heavy-duty direct injection diesel engine with simulated turbocharging. Sprays were imaged via the elastic backscatter technique without significantly altering the engine geometry. Light loads (or pilot injections) were also studied because the spray breakup, mixing and vaporization processes can be isolated since they are less influenced by heat feedback from the flame than in a full injection case. The pilot injections included cases with three different fuel amounts (10%, 15% and 20% of the fuel injected in the baseline case, i.e., 75% load and 1600 rev/min) with different start-of-injection timings. Maximum liquid penetration lengths beyond which the fuel is completely vaporized were observed for all the cases studied. The maximum lengths varied from 23 mm to 28 mm for the different start-of-injection timings.

A numerical simulation and optimization study was conducted for a medium speed direct injection diesel engine. The engine's operating characteristics were first matched to available experimental data to test the validity of the numerical model. The KIVA-3V ERC CFD code was then modified to allow independent spray events from two rows of nozzle holes. The angular alignment, nozzle hole size, and injection pressure of each set of nozzle holes were optimized using a micro-genetic algorithm. The design fitness criteria were based on a multi-variable merit function with inputs of emissions of soot, NOx, unburned hydrocarbons, and fuel consumption targets. Penalties to the merit function value were used to limit the maximum in-cylinder pressure and the burned gas temperature at exhaust valve opening. The optimization produced a 28.4% decrease in NOx and a 40% decrease in soot from the baseline case, while giving a 3.1% improvement in fuel economy.

Airflow characteristics surrounding non-evaporating transient diesel sprays were investigated using a 6-hole injector. Particle Image Velocimetry (PIV) was used to measure the gas velocities surrounding a spray plume as a function of space and time. A hydraulically actuated, electronically controlled unit injector (HEUI) system was used to supply the fuel into a pressurized constant volume chamber at room temperature. The chamber gas densities in this study were 10 kg/m3, 20 kg/m3 and 30 kg/m3. The injection pressure was 96.5 MPa. Two frequency doubled (532 nm) Nd:YAG lasers were used to create coincident laser sheets to illuminate the test section at two instances after start of injection (ASI). The double exposed images of sprays and Al2O3 seed particles were developed and velocity vectors of the gas surrounding the transient diesel sprays were obtained using a numerical autocorrelation PIV method.

A study was performed that takes into account both turbulence and chemical kinetic effects in the numerical simulation of diesel engine combustion in order to better understand the importance of their respective roles at changing operating conditions. An approach was developed which combines the simplicity and low computational and storage requests of the laminar-and-turbulent characteristic-time model with a detailed combustion chemistry model based on well-known simplified mechanisms. Assuming appropriate simplifications such as steady state or equilibrium for most of the radicals and intermediate species, the kinetics of hydrocarbons can be described by means of three overall steps. This approach was integrated in the KIVA-II code. The concept was validated and applied to a single-cylinder, heavy-duty engine. The simulation covers a wide range of operating conditions.